Audi 2014 A8L configuration / mods Overview There are a lot of "hidden features" that are available in other countries that are not enabled in the NA version of the A8. Most of this seems to be to avoid lawsuits. I can't fault Audi for this, people sue each other and everyone around them for stupid things they do themselves. I've use the VCDS system (ex VAG-COM) for years, previously on my 2002 A8L. I've been collecting information on the tweaks I can do, and the ones highlighted in green are those I have done and verified. Yellow means I want to do them, and they are not done yet. I need to thank two people here for a lot of information I used starting this list, Jack88 from the Ross-Tech forum, and Jan from Trick77. VCDS programming If you don't know what this is, you should buy one, not cheap but great support. Don't buy the clone programming dongles. You will have issues and they will not support you. Go to Ross-Tech.com and buy one. module passwords used for the "security" option in certain controllers 09 - Central Electrics: 20113 10 - parking: 71679 ?? 13 - Auto Distance Regulation: 20103 6D - Trunk Electric: 12345 driving mode display - 02 - Auto Trans Change the driving mode display from D or S to D1, D2, or S1 S2 etc. to show the gear you are in [adaptation] "Single Gear Display" default was D off / S off changed to D on/S oner] -> Byte 1 -> Bit 1 change 1 to 0. seat heater timing - 08 - Auto HVAC- done need to verify Disable the automatic change in seat heating level 3 to level 2 after 10 minutes. [10-Adaptation] IDE02371 Time Stage 3 to Stage 2 default was 10 (minutes), set to 0 (never change) recirculation hold last setting - 08 - Auto HVAC- done need to verify recall last state of recirculation button to recall the last state, So if the button is pressed on it will stay on default until turned off. 1. 08 Auto HVAC 2. MOD - UDS Adaptation Channel: IDE01476-Store recirculation air setting for terminal 15 off seat ventilation - 09 - Central Electronics Change speeds of seat ventilation [adaptation] IDE10322-MAS01366-Seat ventilation; micro adjust.-Stage 3 default 0, change to up to 10% (10% IS MAX VALUE) IDE10322-MAS01365-Seat ventilation; micro adjust.-Stage 2default 0, change to up to 10% (10% IS MAX VALUE) IDE10322-MAS01364-Seat ventilation; micro adjust.-Stage 1 default 0, change to up to 10% (10% IS MAX VALUE) seat heating - 09 - Central Electronics 2. ORIGINAL - UDS Adaptation Channel: IDE10321-MAS01364-Seat heater: micro adjust.-Stage 1 Stored value 0 °C ( 5 DEGREES + OR - IS MAX VALUE) 3. ORIGINAL - UDS Adaptation Channel: IDE10321-MAS01364-Seat heater: micro adjust.-Stage 2 Stored value 0 °C ( 5 DEGREES + OR - IS MAX VALUE) 4. ORIGINAL - UDS Adaptation Channel: IDE10321-MAS01364-Seat heater: micro adjust.-Stage 3 Stored value 0 °C ( 5 DEGREES + OR - IS MAX VALUE) Audi Drive select ADS - 09 - Central Electronics change the drive select options and order Set ADS to specific preset Comfort, Auto, Dynamic or Individual [09 – Cent. Elect.][Security Access - 16](VCDS will have popup telling you the access code, mine was 20113) [Adaptation - 10] -> Channel 63 Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual [Adaptation - 10] -> Channel 64 Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual [Adaptation - 10] -> Channel 65 Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual [Adaptation - 10] -> Channel 66 Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual *Note all four channels needs to be set to the same value. (Uncomfirmed) can set more driving modes, max 6 at a time 1 = Individual 2 = Comfort 4 = Auto 8 = Dynamic 16 = Offroad 32 = Efficiency 64 = Race need to read these channels and see what is there.. this is not complete yet Lights, Euro style parking lights - 09 - Central Electronics activated by turn signal lever position [Coding - 07] -> Long Coding Helper -> Byte 9 Bit 0 - Set to 1 Lights, DRL and.. - 09 - Central Electronics various settings to keep DRLs on, or other lights with high beams Enable DRL to include the following:[Coding - 07] -> Long Coding Helper -> Byte 2 Bit 1 = DRL with Front Side markers Bit 2 = DRL with High Beams Bit 3 = DRL with Fog lights Bit 4 = DRL with LEDs Bit 6 = DRL with Side markers Bit 7 = DRL with Tail lights Lights, fog lamps and ... - 09 - Central Electronics Enable fog lamp to come on for the same side as that turn signal [Coding - 07] -> Long Coding Helper -> Byte 4 Bit 0 - Check the box or change :Bit 0 set to 1 Lights, independent fog lamp control - 09 - Central Electronics Enable Independent Fogs control with high beams [09 – Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 4 Bit 1 – (Front) Uncheck the box or change :Bit 1 to 0 Bit 2 – (Rear) Uncheck the box or change :Bit 2 to 0 Lights, Enable/Disable Parking Lights - 09 – Central Electronics enable or disable the parking light function [Coding - 07] -> Long Code Helper -> Byte 9 – 0=off/1=on Bit 0 – Parking Light Function Lights, front turn signal as parking light - 09 - Central Electronics [Coding - 07] -> Long Coding Helper -> Byte 10 Bit 0- Check the box or change :Bit 0 to 1 Lights, Disable amber corner lights - 09 - Central Electronics [Coding - 07] -> Long Coding Helper -> Byte 10 Submodule 0 Bit 3 - Set to 0 to disable amber side markers (U.S. vehicles) Adjust LED brightness - 09 - Central Electtronics [Security Access - 16] (enter security code. One of the default codes is- 20113) [Adaptation - 10] -> Channel 3 Set between 5 and 100 Wipers / washers - 09 - Central Electronics Enable / Disable After-wipe of windscreen wipers Coding - 07 -> Byte 1Bit 3 1= active, 0=disable Wipers / washers - 09 - Central Electronics Set Headlight washer – Duration (values in milliseconds) [Security Access - 16] [Adaptation - 10] -> Channel 6 change to e.g. 500 Set Headlight washer activation Delay - Central Electronics How many times you can activate the regular washers without activating the headlight washers [Security Access - 16] [Adaptation - 10] -> Channel 25 change to e.g. 3000 Ambiance lighting - 09 - Central Electronics can add adjustable footwell lighting, mostly through green menu Coming / leaving home functions - 09 - Central Electronics need to investigate, I don't understand these yet Set Coming Home Time– Duration[Security Access - 16] [Adaptation - 10] -> Channel 43 change to e.g. 30 Activate/Deactivate Leaving Home Function[Security Access - 16] [Adaptation - 10] -> Channel 46 change to 0=off / 1=on Coming Home – Ambient Light Threshold for activation[Security Access - 16] [Adaptation - 10] -> Channel 37 change from 0-7 Enable/Disable Coming Home and Leaving Home Function [Coding - 07] -> Long Code Helper -> Byte 6 – 0=off/1=on Bit 1 – Coming Home Bit 2 – Leaving Home Lights on warning - 09 - Central Electronics [Coding - 07] -> Long Coding Helper -> Byte 5 Bit 3 - Set to 0 to disable "lights are on" warning when you open the door. Change parking camera speed deactivation -10 - Parking change deactive speed of camera, up to 20 km/h [Adaptation - 10] -> Channel 23 Change to 20 (max value in km/h) default value is: 10 (km/h) Date display - 17 - Instruments adjust date display - need to investigate [Coding - 07] -> Long Code Helper -> Byte 7 – Use dropdown to select date format Lap timer DIS - 17 - Instruments can set lap timer, also sets oil temp, can calibrate fuel mpg couldn't do this on my car, the windshield washer stalk needs to have the reset button *Oil temperature will be enabled as well:[Coding - 07] -> Long Coding Helper ->Byte 1 Bit 3 change from 0 to 1Or Check the box for "Lap Timer active" if available. Gauges - 17 - Instruments - done instrument needle sweep at startup [Coding - 07] -> Long Coding Helper -> Byte 1 Bit 0 - Check the box for "Gauge Test/Needle Sweep active" Warnings - 17 - Instruments remove seatbelt chime [Coding - 07] -> Long Coding Helper -> Byte 0 Bit 2-4 – Seat Belt Warning inactive (not complete) Oil Temp - 17 - Instruments display oil temp, not tested [Coding - 07] -> Long Coding Helper -> Byte 10 Bit 1 Upshift display - 17 - Instruments [Adaption - 10] -> Upshift Display in center panel -> Use dropdown to activate/deactivate (untested) ACT Control on FISSelect Control unit 17 (Dashboard)AdaptationSelect channel cylinder deactivationChange enabled (default value: No display) alarm beep - 46 - Comfort System can set double beep upon disarm [46 - Central Conv.] [Adaptation - 10] -> Channel 63 Add 4 (bit 6??) remote control of windows/sunroof - 46 - Comfort System allows opening/closing windows and sunroof with remote [Coding - 07] -> [Long Coding Helper] -> byte 2, bit 2 set to 1 or Check the box for "Comfort Operation: Remote Control active" Then go into MMI: CAR->WINDOW->SUNROOF->ON *Note, the sunroof can only be tilted with the remote after activation in the MMI. trunk remote operating - 46 - Comfort System Close the trunk (a.k.a. boot) remotely using the key fob and/or interior trunk switch in the door (and retain the opening feature)I did this because to close the trunk from the door switch, you had to pull and hold it until it closed, the change lets a single pull close the trunk First go to Module 46 (central convenience), coding, long coding helper byte 2, bit 2 "Comfort operation: Remote control active" should be checked, if it isn't, check it. Then got to module 6D (Trunk Electrics), security access and enter security code "12345". Then still in Module 6D, click Adaptation. Now there are 8 channels to be concerned with, they all look pretty similar. Basically you want to set "Tap" for closing the trunk with the door switch, and "Tap" for closing the trunk with the remote. IDE02134-MAS04214 remote key tap openIDE02134-MAS04215 remote key tap closeIDE02134-MAS04216 remote key touch openIDE02134-MAS04217 remote key touch closeIDE02136-MAS04214 remote unlocking switch tap openIDE02136-MAS04215 remote unlocking switch tap closeIDE02136-MAS04216 remote unlocking switch touch openIDE02136-MAS04217 remote unlocking switch touch close the one I wanted active are the tap close ones, they were not active stock. Defaults were (need to fill in) also there may be settings for the rear lid opening button defaults below: Activation using rear lid opening button in remote key - Touch function for opening: not activeActivation using rear lid opening button in remote key - Tap function for opening: activeActivation using rear lid opening button in remote key - Touch function for closing: activeActivation using rear lid opening button in remote key - Tap function for closing: not activeActivation using rear lid remote unlocking switch - Touch function for opening: not activeActivation using rear lid remote unlocking switch - Tap function for opening: activeActivation using rear lid remote unlocking switch - Touch function for closing: activeActivation using rear lid remote unlocking switch - Tap function for closing: not active Adaptive brake lights - 46 - Comfort System [Coding - 07] -> Long Coding Helper -> Byte 8 Bit 0 – Emergency Brake Flashing via Turn Lights active (1 = active) Bit 1 – Emergency Brake Flashing via Brake Lights active (1 = active) Disable key warning - 46- Comfort System [Coding - 07] -> Long Coding Helper -> Byte 9 Bit 7 set to 0 (Uncheck) Enable/disable auto locking - 46- Comfort System [Coding - 07] -> Long Code Helper -> Byte 5 – 0=off/1=on Bit 4 – Auto lock Bit 5 – Auto Unlock reverse mirror tilt - 52 - Door Electronics, passenger Enable Reverse mirror tilt [Coding - 07] -> [Long Coding Helper] -> Byte 4 Bit 4 and Bit 2 set to 1 parking brake - 53 - Parking Brake release without stepping on brake [Security Access - 16] (Enter code presented by program) [Adaptation - 10] -> Channel 4 Set to 0 parking brake - 53 - Parking Brake release without putting on seatbelt [Security Access - 16] (Enter code presented by program) [Adaptation - 10] -> Channel 7 Set to 0 hidden MMI menu / "green menu" - 5F - Information Electronics needed to make a number of settings, basically tells car a device is there, and also if you can "see" the menu Hidden Menu in MMI Navi Plus (3G): (Only for Navigation Equipped Cars) [Adaptation - 10] -> Channel 6 -> Change 0 to 1 to bring up the hidden menu:press menu and car, sometimes car just a bit aheadhold for 6 seconds or until mmi blinks CD ripping - 5F - Information Electronics coding >> long coding byte 24 >> bit 5 change to 1 now select adaption look for copy multimedia data, look for optical drive off, set to on reboot mmi so far in VCDS, no label file, cannot change byte 24... Auxillary ventilation - 5F- Information Electronics can set fans to run after car stops or at preset times Disable data entry warnings at speed - 5F- Information Electronics Allows or restricts your entering data while moving, the default is not over 15 kmh and you have to slow to 10 to re-enable. [adaption] speed threshold (ch 2?) speed at which if you exceed you cannot set datadefault 15 (kmh), I set mine to 250 (seems a magic number or max) speed delta (ch 3?) speed you have to "drop" to in order to re-enable data inputdefauly 10 (kmh), I set mine to 250 TPMS - 5F - Information Electronics set tire pressure monitoring system complicated setup, I already have it enabled VIM / Video In Motion - 5F - Information Electronics allows video in motion [Advanced ID - 1A] Note 1st Serial number, If there is more than one serial number field, use the first one! [Security Access] Enter Digits 6, 13, 10, 14, 11 of the 1st Serial number, or use an online calculator as the input Press "Do It!". If you receive a "code not valid" message try the alternate code. If neither code works it's likely that your control module doesn't support VIM. [Adaptation - 10] -> Channel 48 press read Set value to to 255 press test (why?) press save exit Reset MMI my 1st serial number was phone voice control - 77 - do not change if you have mmi voice control already green menu / hidden menu functions Note: many commmands need an mmi reset, mmi + top right softkey + menu hold for 2 seconds until mmi display blanks battery status bar apparently does not work on 3G+ systems “car” >> “cardevextdevicelist”Check the “Battery” checkbox“carmenuoperation”Set the battery value to 5 Enable Import CDs to MMI's HD does not work on 3g+ systems Main/Diagnose/Settings Import Media Set to 4 of 4 "Copy/Ripping" CD to be ripped must be inserted in player below the mmi. http://www.vwaudiforum.co.uk/forum/showthread.php/178271-OBDeleven-first-use-enabling-rip-CD-s-to-MMI-quot-Jukebo?highlight=Jukebo Stuff to research First, the green menu has several important menus that control functions and menus to control the functions cardevicelist this seems to be where the devices are indicated to be present or not to the MMI system. I have listed the ones that were not checked on my car. Most make sense, I don't have that hardware. air condition aux heating not checked headup display not checked adaptive cruise control suspension tyre pressure control rdk interior light exterior light park distance control rearview camera wiper doorlocking mirror not checked onboard computer clock service intervall central units master ZEM compass not checked (I checked this, shows compass on VC) charisma lane departure warning hca lane change assist swa braking way reduction awv seat memory front seat memory rear not checked hybrid not checked universal garage dr open night vision not checked sideview camera not checked rev seatbelt tens RGS traffic sign rec VZE not checked rear seat ent not checked weariness recog. MKE not checked cardevicelist_2 seat heating not checked tilt angle display not checked carextdevicelist mfl vin battery level gauge not checked (i checked it) oil level gauge sliding roof not checked trailer not checked driver monitoring not checked programmed keys carfunctionlist pdc entertainment dimming 1 not checked pdc entertainment dimming 2 am/fm toggle oil level gauge extended bord book MFL jokerfunction not checked MFLO type (STD/PA) not checked carmenuoperation adaptive cruise control 5 interior light 5 parking system 1 braking way reduction aww 5 lane departure warning hca 5 lane change assist swa 5 exterior light 5 battery level gauge 0 (changed to 5) window 5 air condition 5 on-oard computer 5 tyre pressure control rdk 9 wiper 5 service intervall 7 seat memory 1 central lock 5 compass 0 (changed to 5) charisma 5 oil level gauge 5 veh identno activate VIN 7 clock 7 suspension 5 headup display 0 central unit master zem 7 hybrid 0 bord book 3 unig garage dr opener 1 night vision 0 sideview camera 0 rev seatbelt tens. RGS 5 mfl joker key 0 aux heating 0 traffic sign recog VZE 0 rear seat entertainment 0 weariness recognition MKE 0 programmed key (ang. schl.) 7 tilt angle display 0 Audi interior lighting controls, found on a forum (forgot to credit the author - Sorry) A few things to know before we start: 1) If the overhead dome lamps are on (even a little), the rearview mirror dimming feature is disabled. 2) If the rear sun shade is raised, the rearview mirror dimming feature is disabled. 3) There are 4 "patterns" in the Background Lighting menu. Only one can be used at a time. They cannot be combined to achieve a group affect, aside from the group affect that each pattern already contains. 4) The button in front of the sunroof switch, in the overhead console, will immediately cancel all interior lighting, and the rearview mirror dimming begins working immediately. 5) To access the Background Lighting menu in the MMI, push the Car button, then push the Systems button, and then select Background Lighting from the menu. There are 4 "pattern" choices to work with; Highway, City, Cockpit, and Rear. There is also an Off selection that cancels whatever Background Lighting pattern you currently have active. Each pattern lights up specific combinations of interior lights. By dialing up or down, you increase or decrease the brightness of the lamp combination included in the selected “pattern.” This is a list of which lamps each pattern controls: Highway – Front & rear door strip lamps Rear – Rear foot well lamps, rear dome lamps, and rear door strip lamps Cockpit – Front & rear door strip lamps, front dome lamps (mirror dimming will not work), and (this one is weird but…) passenger front foot well lamp (not driver’s side) City – All interior lamps lit to desired brightness; Front & rear door strip lamps, front & rear dome lamps (mirror dimming will not work), front & rear foot well lamps (including driver) Now (finally, geez!), here’s the skinny on how it’s done: 1) Access the Background Lighting menu in MMI 2) Select the pattern that contains the collection of lamps you want lit, and plunge the big knob. 3) Dial up or down to the desired brightness and plunge the big knob 4) Press the Return button on the center console to save your settings and go back to the main Car (suspension) menu